Yaskawa Industrial Servo Motor Japan 209W 2.0A InsA Servo Motor SGMCS-10C3C11

Item Description

Manufactured by YASKAWA ELECTRIC

• YASKAWA ELECTRIC
• SGMCS-10C3C11​
• SGMCS-10C3C11​
• SERVO MOTOR.
• 209W
• 200V
• 2.0A
• 5.0 N.m
• Ins A
• 2000r/min
• Single-phaseType
• Efficiency:IE
• High Frequency
• AVAILABLE
• REBUILT SURPLUS
• NEW SURPLUS
• REPAIR YOURS
• 24-48 HOUR RUSH REPAIR
• 2 - 15 DAY REPAIR
• 2 YEAR RADWELL WARRANTY

OTHER SUPERIOR PRODUCTS

CAUTION

• Conduct trial operation on the servomotor alone with the motor shaft disconnected from machine to avoid any unexpected accidents. Failure to observe this caution may result in injury.

• Before starting operation with a machine connected, change the settings to match the parameters of the machine. Starting operation without matching the proper settings may cause the machine to run out of control or malfunction.

• Forward run prohibited (P-OT) and reverse run prohibited (N-OT) signals are not effective during zero point search mode using parameter Fn003.

• When using the servomotor for a vertical axis, install the safety devices to prevent workpieces to fall off due to occurrence of alarm or overtravel. Set the servomotor so that it will stop in the zero clamp state at occurrence of overtravel. Failure to observe this caution may cause workpieces to fall off due to overtravel.

• When not using the normal autotuning, set to the correct moment of inertia ratio. Setting to an incorrect moment of inertia ratio may cause vibration.

• Do not touch the SERVOPACK heatsinks, regenerative resistor, or servomotor while power is ON or soon after the power is turned OFF. Failure to observe this caution may result in burns due to high temperatures.

• Do not make any extreme adjustments or setting changes of parameters. Failure to observe this caution may result in injury due to unstable operation.

• When an alarm occurs, remove the cause, reset the alarm after confirming safety, and then resume operation. Failure to observe this caution may result in injury.

• Do not use the servo brake of the servomotor for ordinary braking. Failure to observe this caution may result in malfunction





Industrial Vertical Submersible Sewage Pump , Electrical Wastewater Submersible Pump For Septic Tank Application: Wastewater lift station; Municipal wastewater treatment plant; Building wastewater treatment system; Animal & poultry farm wastewater treatment system; Hospital, school, community etc. Wastewater treatment system; Food, paper, mining, textile, leather, chemical industry etc. wastewater treatment system. Water purification system. Features: NON-CLOG IMPELLER Well statically & dynamically balanced Non-Clog impeller is designed to allow sizable spherical solids to pass the plow passage easily without clogging.It adopts rigorous technics so that vibration and noise can be farthest reduced. LEAKAGE DETECTOR Built-in leakage detector in the oil chamber can dectet leakage from the damage of the mechanical seal. (The power lower than 15KW is optional,not lower than 15KW is standard accessories.)Built-in leakage detector in the wiring box can check if a leak in it,The leakage detector offers pump an automatic protection. (Not stamdard accessories, the power not lower than 18.5KW is optional) HEAT-DETECTOR Built-in heat protector in motor, it secures the protection of motor against burning out. (The power lower than 15KW is optional,not lower than 15KW is standard accessories.) overload & overheating to Built-in heat protector in bearing, when the bearing is abnormal and the temp- erature rises to disconneting temperature, the protector automatically cat off power supply to protect the bearing.(options) COOLING JACKET (OPTIONAL) Pumps make use of inner pressure of pump cauvty to make liquid contiwue entering to space between cooling house and motor outer, to take away the heat the motor produces. ( The power not lower than 18.5KW is optional) Points for attention before starting equipment: # # Check the insulation condition of the stator winding with a 0-500V meter before starting the water pumps. # Check whether the power and the voltage frequency used are in line with those listed on the label. # Don't connect the electric wire of the water pump with the power source without any protective device (which may lead to the burning of the motor due to open-phase and overload). Refer to the connection method of the submersible pump. (refer to Page 9 for details). # Before installation, check the rotation direction of the motor, the correction rotation direction is that the motor rotates counter-close seen from the suction direction of the impeller. If the rotation direction is not right, the connection positions of any two phases in three phases shall be shifted to get it rotate in a correct direction. # Check whether the grounding wire is earthed properly. # Check whether the operation of the level controller is in normal so as not to affect the service life of the submersible motor. # Close the gate valve of the outlet pipeline and start the motor. Under the circumstance that the gate valve of the outlet pipeline is shut, the pump cannot rotate over 3 minutes continuously. Monitor the motor current by switching on the gate valve and control the current within the rated range, and check whether the pressure of the pressure gauge and the operation of the pump are in normality, and refer to the trouble shooting sheet to remove in case of abnormality. # Operation without water is prohibited. # Submerging cable sockets of the motor into water is prohibited. # Lifting and hanging the motor with the motor cable is prohibited during the transport and installation processes. Construction: - - - - No. Name Material GB JIS 1 Neck bolt 2Cr13 SUS420 2 Heat-Protector - - 3 Motor cover HT200 FC200 4-1 Bearing - - 4-2 Bearing - - 5 Cooling house flange Q215A LSS330 6 Shaft 2Cr13 SUS420 7 Rotor - - 8 S

Shenzhen Wisdomlong Technology CO.,LTD Mainly engaged in automation parts, PLCS,DCS,sensors, relays, dirves,encoder, servo drive,soft starter,touch screen,instrument,process control,electric transmission and factory automation aspects of the project design,software programming,technical service and staff training. Our company locats at the central of China,Shenzhen, Guangdong Province. With rapid development, Wisdomlong serves fields of automation in global markets, Our business covers five continents throughout the world with the basic conviction of honest, the international management of customer-centered concept and purpose of bringing convenience to customers. We have confidence to bring our customers more substantial profit with high-quality service and reasonable prices. Choosing us,you will choose a sincere friend and reliable partner. Please feel free to contact us if you are a global manufacturer of high quality brand products who desires to enter the Chinese market or who searches for a Chinese agent.We would like to create a brilliant future with friends in domestic and overseas. All goods sold have one year warranty.

The company with domestic and international numerous well-known brands supplier to build have extremely good relations of cooperation, in Japan, South Korea, southeast Asia, Africa, Europe and the United States, and formed a stable and efficient supply network. The agent and the products are widely used in machinery, equipment manufacturing, electric power, metallurgy, petrochemical, automobile manufacturing industry, paper making, chemical industry, medicine and aerospace industries.

Our Main Brand:

MITSUBISHI

YASKAWA

PANASONIC

GE FANUC

EMERSON

FISHER-ROSEMOUNT

HONEYWEL

ABB

AB

SHNEIDER MODICON

SIEMENS

................