Compact Structure Centrifugal Filter Separator Outlet Pressure ≦ 0.4Mpa

Compact Structure Centrifugal Filter Separator Outlet Pressure ≦ 0.4Mpa​

Separating Function

(1) Liquid flow
Separation takes place in the separator bowl to which unseparated oil is fed through the inlet pipe. The oil is led by the distributor towards the periphery of the bowl.
When the unseparated oil reaches the slots of the distributor, it will rise through the channels formed by the disc stack where it is evenly distributed into the disc stack.
The oil is continuously separated from water and sludge as it will flow towards the center of the bowl. When the cleaned oil leaves the disc stack it rises upwards and enters the paring chamber. From there it is pumped by the paring disc and leaves the bowl through the outlet.
Separated sludge and water move towards the bowl periphery. In purification separated water rises along the outside of the disc stack, passes from the top disc channels over the edge of the gravity disc and leaves the bowl into the common sludge and water outlet of the separator.
Heavier impurities are collected in the sludge space outside the disc stack and are discharged at intervals
through the sludge ports.
(2) Water seal in purification
To prevent the oil from passing the outer edge of the top disc and escaping through the water outlet, a water seal must be provided in the bowl. This is done by filling the bowl with water through the water inlet, before unseparated oil is supplied. When oil feed is turned on the oil will force the water towards the bowl periphery and an interface is formed between the water and the oil. The position of the interface is determined by the size of
gravity disc.
(3) Displacement of oil
To avoid oil losses at sludge discharge, displacement water is fed to the bowl. Prior to a discharge the oil feed is stopped and displacement water added through the water inlet. This water changes the balance in the bowl and the interface moves inwards to a new position, increasing the water volume a new position, increasing the water volume in the sludge space. When the sludge discharge takes place sludge and water alone are discharged.
Sludge discharge occurs while the displacement water is still flowing. A new water seal will therefore establish immediately afterwards. The oil feed is then turned on again.
(4) Gravity disc
In the purification mode, the position of the interface can be adjusted by replacing the gravity disc for one of a larger or smaller size. A gravity disc of a larger size will move the interface towards the bowl periphery, whereas a disc of a smaller size will place it closer to the bowl centre.
The sizes of the gravity discs are normally stamped on the discs.
(5) Clarifier disc
In the clarification mode, the gravity disc is replaced by a clarifier disc which seals off the water outlet. In this case no water seal is required and consequently there is no oil/water interface in the bowl. The clarifier disc is an optional disc with a hole diameter of 40 mm. This disc is not shown in the nomograms.

Application:

Successful applications:

Separation of the extract( such as penicillin, vitamin, Colibacillus, Antibiotics, Hormones, etc.), Microbial Concentration, Concentration and Clarification of Fermentation Broth, Blood Separation, etc.

In penicillin and 6-APA production process, disk separator is mainly used in extraction, reextract, washing extract.

Introduction of Company:

Juneng Group is a large scale manufacturer of industrial products in China with its subsidiaries namely Juneng Machinery(China) Co., Ltd and Jiangsu Juneng Machinery Co., Ltd. The group principally engaged with the in-house research & development as well as manufacturing of various industrial filters, separators and pumps.

The Company is proud to be the leader in such industry with Fats industry, Chemical industry, Pharmaceutical industry, Beverage industry, Petrol - chemical industry, and now is one of the well-know producers and suppliers in the world.

The company now has its three production bases with a total capacity of 280,000 square meters in Nanjing City and Yixing City of Jiangsu province, permanent workforces not less than 1300 people and the production line is well equipped with more than 1500 units of advanced production equipment and test instrumentation.

Product Specifications:

QA/QC Department

1.Factory visit/ audit is required prior to other purchase

2.Inspection of material is required during in process manufacturing & prior shipment

3.Compliance to technical requirements

Track Records:

1. With the outstanding track records, our products are widely applied into different industries

2. The key factors of our success are to constantly fulfilling customer's requirement and exceed their ecpection.

3.We are loking forward to your guidance, opinion and suggestions that would be a long term mutual beneficially business relationship.

Juneng Group is a large scale manufacturer of industrial products in China with its subsidiaries namely Juneng Machinery (China)Co., Ltd . The group principally engaged with the in-house research & development as well as manufacturing of various industrial filters, separators and pumps. The Company is proud to be the leader in such industry with approximately 80% domestic market share in Oils & Fats industry, Chemical industry, Pharmaceutical industry, Beverage industry, Petrol-chemical industry, and now is one of the well-known producers and supplies in the world.